Anchoring a shade structure for wind
Most shade structures fail the same way: a tarp catches a gust and the frame has too little holding it down. Here’s the anchoring plan the CampShade planner uses, how many straps each size needs, and when to take the tarps down.
A shade frame has two jobs in the wind: keep its feet where they are, and keep its top from leaning and lifting. Each job gets its own hardware.
- Every pole’s foot is held down. Each pole stands in a flange plate nailed down with 8" spikes: 4 at the corner poles, 3 at the rest. Pin the plates before any strap goes on. On pavement, a 50 lb sandbag sits on each plate instead.
- The top is strapped. A 1" × 15' ratchet strap (500 lb working load) runs from a pole’s top fitting down to a ground anchor 5–7 ft out. Straps stop the frame racking sideways and resist the lift a tarp puts on it.
Where the straps go
The planner straps every outside corner, then every 20 ft along each side, counted from a corner. A 20 ft side needs nothing between its corners. A 30 ft side gets one strap between. A 40 ft side gets one in the middle.
- Ratchet strap to its anchor
- 90° corner
- 4-way (edge)
- 5-way (inside)
A 40×30 takes 8 straps.
| Size | Corners + every 20 ft | Every outside pole |
|---|---|---|
| 20×20 ft | 4 | 8 |
| 30×20 ft | 6 | 10 |
| 30×30 ft | 8 | 12 |
| 40×30 ft | 8 | 14 |
| 40×40 ft | 8 | 16 |
The first column is what the planner lists. Burning Man’s own camping tips go further: put a bolt at each outside pole, and some inside poles if needed. On the playa, where the same page notes that “75-mph winds are a common occurrence,” the second column is worth the extra bolts and straps. Each extra strap needs its own anchor.
Which anchor for your ground
| Ground | Anchor | How |
|---|---|---|
| Playa, hard dirt | 1/2" × 18" hex lag bolt and washer | Drill a 3/8" pilot hole, drive it with an impact driver and a 3/4" socket. It backs out clean at teardown. Burning Man notes 12–14" lag bolts are common there; the planner specs 18". |
| Grass, soft soil | 15" auger anchor | Screws into the ground and back out. Reusable. |
| Pavement | 50 lb sandbags | Nothing can be pinned or bolted, so the planner uses two sandbags (100 lb) at each strap anchor and one on each flange plate. Ship them empty and fill on site. |
For a 30×30, that’s 8 lag bolts on playa, 8 augers in grass, or 32 sandbags on pavement (16 at the anchors, 16 on the plates), plus 8 straps in every case.
Wind walls
A wall panel blocks sun and blowing dust, and it catches wind like a sail. The planner gives every pole along a wall its own steep tiedown, a strap to an anchor 12–24" out, and that pole is anchored before its bay’s panel goes up. A straight wall of n 10 ft bays adds n + 1 straps and anchors. Walls that meet at a corner share that corner’s pole.
- Wind wall
- Wall tiedown, 12–24" out
- Ratchet strap to its anchor
One 30 ft wall: 8 perimeter straps + 4 wall tiedowns = 12.
When to drop the tarps
Straps hold the frame. Past a point, nothing holds a tarp. The planner’s rule:
Drop tarps and wall panels when a Wind Advisory is issued or the forecast reaches sustained 31+ mph or gusts 46+ mph, whichever comes first. Don’t wait for a High Wind Warning.
The National Weather Service generally issues a Wind Advisory for sustained winds of 31–39 mph for an hour or more, or gusts of 46–57 mph, and a High Wind Warning from 40 mph sustained or 58 mph gusts. Each forecast office sets its own criteria, and where strong wind is routine an advisory may not be issued at all. That’s why the rule also goes by the forecast numbers.
- Walls first, then tarps. Take the fabric down before you loosen any strap.
- Re-tension every morning. Straps loosen as a frame settles.
- Leave the frame up and strapped. Bare EMT gives the wind very little to push on.
What this isn’t
This is anchoring advice from field practice and your site’s wind history, not an engineered rating. A platform people climb on, or anything taller or more unusual than this grid, needs an engineer, not a guide.